§ 28. Highway corridor (HC) district.
28.1
General purpose and description. The highway corridor (HC) district is intended to provide a regional destination for high quality retail, commercial and business opportunities, good jobs, and utilize the highest and best uses to enhance the taxable yield for the city and the tax increment finance district (TIF) where applicable. The uses envisioned for the district will be compatible with the high visibility and high traffic conditions of the corridor with high quality architectural, streetscape and landscape aesthetics. Convenient access to major thoroughfares and collector streets, internal connectivity, as well as pedestrian oriented circulation in building placement and parking lots utilizing SMART Code and sustainable form-based design elements are also primary considerations. The boundaries of the highway corridor (HC) District are indicated on the revised future land use map of the comprehensive plan. All zoning change requests as well as annexations requesting permanent zoning on properties located within the highway corridor (HC) district shall be rezoned in accordance with the comprehensive plan and future land use map.
28.2
Permitted uses.
A.
Those uses listed for the HC district in section 32 as "P" are authorized uses permitted by right and are anticipated to be primarily located along the highway frontages; those uses indicated by an "R" are permitted uses which are restricted and cannot be located less than 700 feet from the highway right-of-way (IH 20, U.S. Hwy. 80, Spur 557, proposed outer loop and proposed Alternate U.S. 80 alignment) such as non-retail uses which are not dependent upon direct exposure to high visibility/high traffic for success; and those uses indicated by an "S" are permitted only by the issuance of an specific use permit (SUP) which must be approved by ordinance utilizing procedures set forth in section 31B, those uses indicated by a "T" are permitted only by the issuance of temporary use permit which must be approved utilizing procedures set forth in subsection 38.10.
B.
Certain temporary uses indicated by a "T" may be approved on a case by case basis upon receipt of an approved temporary use permit issued by the director.
C.
All other uses not specifically indicated by a "P", "R", "S", or "T" are prohibited within the highway corridor (HC) district.
D.
New central business districts are allowed to be created in the highway corridor (HC) district as a separate CBD district approved by the city council and shall be considered to be in accordance with the comprehensive plan and future land use map. Uses permitted as listed in the use charts in section 32 under CBD column.
28.3
Height regulations.
A.
Maximum height.
1.
No height limits for structures within 700 feet of the highway right-of-way otherwise six stories or 75 feet. All structures must meet the minimum setbacks in regards to proximity to residential structures. Height may be further restricted by FAA guidelines.
2.
One story for accessory buildings.
3.
Other (section 38).
28.4
Area regulations.
A.
Size of lot.
1.
Minimum lot area. Ten thousand square feet.
2.
Minimum lot width. One hundred feet.
3.
Minimum lot depth. One hundred feet.
B.
Yards, setbacks and build-to lines.
1.
Primary roads. Primary roads are defined as either the major highway or those frontage or access roadways running parallel but divided from the major highway traffic lanes within the same right-of-way providing local but limited access to and from property adjacent to the highway.
a.
A minimum of 20 feet immediately adjacent to the highway right-of-way line shall be a landscape buffer (see requirements below).
b.
Sidewalks, monument or directional signs, lighting, public art or outdoor fixed furniture may be placed in the landscape buffer.
2.
Front yard—Secondary roads. All yards adjacent to a secondary road (except primary highway roads see B.1 above) shall be considered a front yard. For the purpose of this section a secondary road is defined as a thoroughfare having direct access to the major highway.
a.
A minimum of ten feet immediately adjacent to the collector right-of-way line shall be a landscape buffer (see requirements below).
b.
Sidewalks, monument or directional signs, lighting, public art or outdoor fixed furniture may be placed in the landscape buffer.
Desirable Design Attribute - Buildings are placed along a "build-to" line with landscape buffer which creates a consistent and strong street wall along the corridor
3.
Front yard—Tertiary streets and other streets. All yards adjacent to a tertiary street or other public streets (except as in B.1 or B.2 above) shall be considered a front yard. For the purpose of this section a tertiary street or other public street is defined as a thoroughfare not having direct access to the major highway but may have access to the frontage roads of the highway or secondary roads.
a.
A minimum of ten feet immediately adjacent to the street right-of-way line shall be a landscape buffer (see requirements below). Buildings placed less than ten feet from the right-of-way line are not required to have a landscape buffer.
b.
Sidewalks, monument or directional signs, lighting, public art or outdoor fixed furniture may be placed in the landscape buffer.
4.
Minimum side and rear yard (not adjacent to a street). Ten feet unless a fire lane is required then a side or rear yard capable of accommodating the minimum required width of a fire lane would apply. If property line is adjacent to residentially zoned property see setback requirement in figure 28-1 below.
5.
Interior side yards. When retail/commercial uses are platted adjacent to other retail/commercial uses and integrated into an overall town center/campus site (i.e., lots/lease spaces abutting one another), no side yard is required provided it complies with the city's adopted building and fire codes.
6.
Minimum side or rear yard adjacent to a residential district. A ratio of 3:1 or three feet of setback for each one foot of height of a commercial structure is required adjacent to any residentially zoned property line (see figure 28-1).
Figure 28-1: Residential Setbacks
28.5
Special requirements.
A.
Maximum lot coverage. Maximum 90 percent impervious coverage (including all buildings, parking areas, sidewalks, etc.).
B.
Driveway spacing (i.e., distance between driveways, measured edge-to-edge). Subject to TxDOT standards and/or other city design standards.
C.
Sidewalks. All sidewalks in nonresidential areas adjacent to streets, in parking lots, yards, or located within landscaped buffers or areas shall be a minimum of six feet in width, sidewalks immediately adjacent to or abutting any building shall be a minimum of eight feet in width, sidewalks located in residential developments of the highway corridor (HC) district shall be a minimum of four feet in width.
D.
Temporary outdoor retail sales. Temporary outdoor retail sales, which involves the outside display of merchandise and seasonal items, shall be limited to the following:
1.
Shall not be placed/located closer than 30 feet to any street right-of-way, or closer than 15 feet to any other property line.
2.
Shall not pose a safety or visibility hazard, nor impede public vehicular or pedestrian circulation, either on-site or off-site, in any way.
3.
Shall not extend into public right-of-way or onto adjacent property.
4.
All outside display items shall be removed at the end of business each day (except for large seasonal items such as Christmas trees when permitted by a temporary use permit, see section 38.10).
E.
Open storage Open storage is prohibited within 700 feet of the highway right-of-way and where permitted shall not be located in any front or side yard adjacent to a public street and must be screened in accordance with the provisions of section 36 (i.e., cannot be visible from any public street or adjacent property). However, a periodic temporary outdoor retail sale, which involves the outside display of seasonal items, is allowed during the appropriate time periods (see subsection C above).
F.
Other regulations. As established in the development standards, sections 33 through 44.
G.
Parking requirements. In order to improve the appearance, convenience of parking lot circulation for both vehicles and pedestrians, parking areas shall be distributed around large buildings (greater than 20,000 square feet in size) in order to shorten the distance to other buildings and help mitigate heat islands (large areas of paved surfaces).
1.
Quantity of spaces shall be in accordance with section 33, off-street parking and loading requirements.
2.
Loading areas should be to the side and rear of buildings; when visible from public roadways or residential properties such areas shall be screened by walls and/or evergreen vegetation. Loading areas shall comply with other applicable provisions of section 33, off-street parking and loading requirements.
3.
No more than two rows of parking shall be located between any building and the right-of-way line of either a highway or primary roadway.
4.
No more than two rows of parking shall be placed between the building and the abutting street on all secondary or tertiary roads and other local public streets for buildings under 20,000 square feet in size. Buildings over 20,000 square feet or if the parking requirement exceeds 100 spaces may have up to 50 percent of the required parking between the front of the building and the abutting secondary thoroughfare or tertiary (local) street.
5.
Rows of parking 150 feet or longer shall have at least one "safe" pedestrian walkway between the rows of cars for every five traffic lanes meeting ADA requirements for width or pass-by areas and protected by curb stops or solid curbing (openings allowed for drainage) oriented in as much as possible toward major store anchors and/or principle pedestrian destinations.
H.
Landscape requirements. Due to the prominent visibility and higher traffic exposure of the highway corridor district it is intended that the aesthetics of this district be enhanced by high quality landscaping, architectural features and site design. Notwithstanding the landscape requirements of section 34 of this ordinance the following requirements are in addition to those requirements and the minimums stated in this section will take precedence over those listed in section 34.
1.
A minimum of 20 feet immediately adjacent to the highway right-of-way line or frontage road shall be a landscape buffer with one large tree required for every 30 feet of frontage. Trees may be clustered in groups or evenly spaced. See section 34 for definitions and other landscape requirements.
2.
In areas where the side or rear of a building faces the highway right-of-way, in addition to the trees a continuous row of screening shrubs or landscape berms shall be placed along the highway right-of-way or frontage road adjacent to the building in order to help screen long expanses of wall or service areas except in areas requiring visibility triangles. For the purpose of design articulation the rows need not be in a straight line but may be meandered, staggered or combined with berms.
3.
All other street frontages shall have a ten-foot wide landscape buffer adjacent to the right-of-way with the same tree requirement as listed above.
4.
Sidewalks, monument or directional signs, lighting, public art or outdoor fixed furniture may be placed in the landscape buffers.
5.
All site plans requiring more than 12 parking spaces shall be landscaped as follows:
a.
All main entrances to parking areas from a thoroughfare shall have landscaped treatments using two or more of the following:
i.
Flowering shrubs or trees.
ii.
Seasonal color beds.
iii.
Rock, boulders, masonry pavers or other decorative materials.
iv.
Decorative retaining walls or wrought iron fencing.
v.
Monument signs.
vi.
Sculptural artwork.
vii.
Fountains.
b.
All parking rows 12 spaces or more shall have landscaped islands on the ends a minimum of 90 square feet in size each.
c.
All parking rows shall have landscaped islands at least every 12 spaces equal to 90 square feet in size. All islands within a parking lot shall have a minimum of one large shade tree. Dense foliage species such as live oak or ornamental pear varieties should be avoided to prevent nuisance bird roosts.
d.
No parking space shall be located further than 60 feet from a landscaped area.
e.
All parking lots shall have a minimum of a five-foot wide landscape buffer on the perimeter of side or rear property lines not adjacent to a street.
28.6
Site design.
A.
Building placement. Buildings should be aligned along a corridor to create a relatively consistent street wall. The application of a build-to line can assist in creating this effect. In order to achieve a consistent appearance along corridors, one or more of the following methods should be used.
1.
All buildings located adjacent to the primary highway frontage road or highway right-of-way shall be located a minimum of 20 feet and a maximum of 90 feet from the right-of-way boundary line regardless of whether the building faces the highway or not in order to accommodate parking and landscaping as required.
2.
All buildings located adjacent to a secondary roadway shall be located a minimum of ten feet feet and a maximum of 80 feet from the right-of-way boundary line regardless of whether the building faces the street or not in order to accommodate parking and landscaping as required. (Exception: When building size exceeds 20,000 square feet and 50 percent of parking is located in front of building according to subsection 28.5.G above.)
3.
All buildings under 20,000 square feet in size adjacent to a tertiary road or other local public street shall be located a minimum of zero feet and a maximum of 55 feet from the right-of-way boundary line regardless of whether the building faces the street or not.
4.
Where buildings are placed less than ten feet from the right-of-way line on-street parking may be allowed if the street cross section design allows for such parking (parking spaces shall observe visibility and other traffic design requirements, i.e. distance from drives and intersections, etc.).
5.
Buildings over 20,000 square feet in size adjacent to a secondary or tertiary road or other local public street may be located further than 55 feet from the right-of-way line but no more than 50 percent of the required parking shall be located between the building and the street right-of-way.
6.
When single tracts or lots of land are developed with multiple buildings, the buildings should be oriented toward internal roadways to form block-like configurations with sufficient walkways to provide safe convenient pedestrian circulation throughout the development. Interconnectivity or cross access with adjacent areas where future development is likely to occur shall be maintained in as much as possible. If development constraints prevent internal circulation then building orientation shall be towards adjacent public roadways.
Desirable design attribute: Multiple building shopping center configured to take advantage of double facades on the internal circulation routes as well as the on the adjacent public streets. This configuration shows a possible alternative when all of the buildings cannot be oriented toward the major roadway.
28.7
Architectural design. The ratio of a building's height to its apparent width which is known as "scale" is a major factor in its overall character and aesthetic appeal. Buildings should respect the human scale and add visual interest to the streetscape. The following guidelines apply to all commercial buildings in the highway corridor district. Bulk and massing of buildings should be consistent with other developments in the corridor to maintain cohesion and visual appeal.
A.
Variation in massing.
1.
Buildings should not have a large, dominant mass or overwhelm surrounding development and should, where possible, be configured in a manner harmonious with topography and vegetation. No large expanse of blank walls shall be allowed along front façades but shall incorporate variation through the use of recesses, projections, windows, columns, horizontal and vertical offsets, awnings, canopies, and similar features.
2.
A building's vertical and horizontal dimensions should be related to each other through the use of bays or articulation that separate the building planes into components with proportions that emphasize neither the vertical nor horizontal dimension beyond a two to three ratio. Buildings with larger footprints should have the façade subdivided into components to provide variation and a hierarchy of components.
3.
The figure below illustrates proportion through a series of facades with various proportions and articulation.
4.
The façade components may be defined through the use of details, fenestration (window placement), roof forms, building materials, awnings or overhangs, and other structures or landscaping elements.
Design elements enhance pedestrian experience: Trees, canopies, furniture, building overhangs, etc.
5.
Structures should include both horizontal and vertical articulation to reduce the apparent bulk and mass of the building.
6.
Buildings should have a clearly defined base, middle and top.
a.
A recognizable base may consist of, but is not limited to: thicker walls, ledges, or sills; integrally textured materials such as stone or masonry; integrally colored and patterned materials such as smooth-finished stone or tiles; lighter- or darker- colored materials different from the body of the building; mullions; or panels. The use of bulkheads and water table trims are strongly encouraged.
b.
A recognizable top may consist of, but is not limited to: dimensional cornice treatments other than just colored stripes or bands, variation in masonry pattern or material or differently colored materials; sloping roof with overhangs and brackets; stepped parapets; or aligned openings and articulations.
Undesirable design attributes: Very few vertical or horizontal articulations
Desirable design attributes: Same street façade as above, but vertical and horizontal articulations and other architectural details have been added for greatly enhanced aesthetic appeal and pedestrian friendliness
B.
Roof forms. Roof forms contribute strongly to the overall scale and bulk of a building. Expansive and blank roof planes can increase the apparent bulk of a structure. To enhance the proportion and scale of nonresidential buildings, the following guidelines for roofs should apply.
1.
Pitched roof forms including gabled, shed, hipped, and compound or double-gabled forms are the preferred styles. However, all pitched roof forms should include eaves and overhangs finished with appropriate trim and accents to provide a dimensional and finished appearance.
2.
Mansard or French-style roofs are appropriate on taller buildings (over two-stories).
3.
The use of dormers to break up the roof plane is encouraged.
4.
Flat roofs may be appropriate on large footprint structures where full gabled roofs would be structurally impractical. However, the use of a flat roof on small footprint buildings is discouraged.
5.
Flat roofs should be enhanced with highly detailed parapets and/or cornices to add dimension to the upper portions of the building.
6.
While parapets may be the primary façade treatment for the screening of flat roofs, variation in the parapet heights or adjustment to the roof forms should be used on large buildings to assist in the articulation of the façade.
The façades shown in the image above represent alternative roof form treatments for large buildings to provide variation in the façade and reduce the visual impact of flat roofs.
C.
Overhangs, canopies and covered walkways. The economic vitality and general quality of life in an often hot climate such as Texas often depends very heavily on providing comfortable pedestrian environments in and around retail, employment centers, restaurants and other high pedestrian traffic areas. Orienting or massing buildings to provide easy access and shorter walking distances to pedestrian destinations as covered previously help mitigate some of the heat island effects of large commercial developments then by adding landscaping and covered walkways the maximum mitigation of the effects of climate can be achieved which results in a vibrant, aesthetically pleasing and pedestrian friendly community. Long flat expanses of projecting upper façade normally seen in older strip shopping centers and single building developments where an excessive amount of signage is usually splashed across every available square foot is also to be strongly discouraged. The following guidelines shall apply to all properties within the highway corridor district:
1.
Upper portions of primary façades shall not overhang lower portions of the façades to provide covered walkways or shade windows unless the overhanging portion of the structure is supported by piers, pillars, or columns of sufficient width and depth to create the appearance of an arcade, colonnade, or other appropriately scaled architecturally integrated feature.
2.
Any portion of a pedestrian walkway immediately adjacent to the southern and western exposures of a building shall have a provision for shade in the form of overhangs, canopies, covered walkways or trees planted in sufficient quantities and locations as to provide adequate shade for pedestrian traffic. Other exposures should also provide for the comfort and appeal of pedestrian traffic in the form of architectural details such as overhangs, canopies, covered walkways or landscaping in order to present a consistent and balanced streetscape.
3.
Horizontal banding applied flat or projecting without supports from the upper portion of a façade to act as a cap to the wall or to provide a "marquee" area for signs or brand identification shall be prohibited.
4.
The projection or cantilevering of the whole upper portion of a primary façade can overshadow the articulation of the building's façade and create a top-heavy appearance and shall be prohibited.
Undesirable design attributes: Projecting flat upper façade with proliferation of unattractive signage and very obtrusive roof billboard
Desirable design attributes: Vertical and horizontal façade articulation with covered colonnade walkway with unobtrusive attractive signage
D.
Awnings.
1.
Awnings shall not project more than six feet from the façade of the building and shall not be counted towards the shade requirement listed in subsection C above. Awnings should be made of durable non-glossy outdoor grade materials in a color that coordinates with the overall design of the building and is compatible with the base colors of the building. Fabric awnings which tend to fade or deteriorate are prohibited. Colors deemed to be inconsistent with these guidelines by the director, including, but not limited to, those affiliated with trademarked or brand affiliated colors shall be required to submit color and material samples to the city for approval by the city council.
2.
Awnings may contain logos or names in trademarked colors of the business to which they are attached if they are in compliance with the sign ordinance as adopted.
3.
Backlit awnings are prohibited.
E.
Freestanding canopies. Freestanding canopies such as those at convenience stores should not overshadow the architecture or scale of the associated buildings or adjacent development. The following standards are intended to promote consistent design of these canopies.
1.
Scale. The height of a canopy should not exceed that of the primary structure.
2.
Roof form. Sloped roof forms such as gabled, gambrel, hipped, mansard or combinations of these types shall be used on all canopies.
3.
Materials. Support columns or piers, roofing, and other exterior finishing materials and colors shall match those used on the primary structure and all elements of the canopy should be proportional to each other.
F.
Rooftop screening. Where a flat roof is appropriate, the roof surfaces and rooftop equipment shall not be visible from the highway corridor or other public rights-of-way or residential property and shall be appropriately screened by parapets or other architectural features.
G.
Sight lines. When planning the location of window openings and areas of outdoor activity in commercial or office developments, the privacy of surrounding residential uses should be respected and direct sight lines into residential areas from proposed nonresidential development should be limited. Likewise, sight lines from adjacent residential areas should be evaluated to minimize impact.
H.
Exterior materials. The following exterior façade standards are intended to promote consistent design and attractive architectural aesthetics within the highway corridor district.
1.
Permitted materials. All exterior façade materials shall be in accordance with section 37 of this ordinance.
a.
A kick plate, knee wall, or other bulkhead of a solid material shall be installed on all facades except the rear of the building where public traffic is not normally allowed or expected to use. If the rear of the building has a public entry or sidewalk then this section will apply.
b.
Visible roofing materials shall be appropriate for the architectural style of the structure. Dimensional asphalt shingles, slate, synthetic slate, decorative metal panels, and tile are permitted materials.
c.
Other materials not listed as prohibited in the section below may be considered on a case by case basis as a primary or accent building material.
2.
Prohibited materials. Exterior façade materials prohibited on facades visible from the public right-of-way are vinyl; aluminum or steel siding; corrugated steel; standard smooth concrete masonry units (cinder block); and highly reflective or mirrored materials like chrome.